DELL SOURCE
Dell 診断プログラム
Dell 診断プログラム メインメニュー
オプション | 機能 |
---|---|
Express Test | デバイスのクイックテストを実行します。通常、このテストは 10~20 分かかり、お客様の操作は必要ありません。最初に Express Test を実行すると、問題をすばやく特定することができます。 |
Extended Test | デバイスの全体チェックを実行します。通常このテストには 1 時間以上かかり、質問に定期的に応答する必要があります。 |
Custom Test | 特定のデバイスをテストします。実行するテストをカスタマイズできます。 |
Symptom Tree | 最も一般的な症状を一覧表示し、問題の症状に基づいたテストを選択できます。 |
Dell 診断プログラム エラーコード
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
---|---|---|---|---|
02XX-XXXX | adaptec.mdm | |||
04XX-XXXX | atidiag.mdm | |||
05XX-XXXX | biosmp.mdm | |||
0700-0119 | The cache improperly changed system memory during an 'invalidate' at line %d. | CPU Memory Motherboard | L1 Data Cache Pattern Test | cache.mdm |
0700-011B | Level 1 cache failure. Cache offset %08Xh miscompared patterns %08Xh and %08Xh. | CPU Motherboard | L1 Data Cache Pattern Test | cache.mdm |
0700-0219 | The cache improperly changed system memory during an 'invalidate' at line %d. | CPU Memory Motherboard | L1 Data Cache Walking Bit Test | cache.mdm |
0700-021A | Cache offset %08Xh miscompare at line %d. | CPU Motherboard | L1 Data Cache Walking Bit Test | cache.mdm |
0700-0319 | The cache improperly changed system memory during an 'invalidate' at line %d. | CPU Memory Motherboard | L2 Cache Pattern Test | cache.mdm |
0700-031C | Level 2 cache failure. Cache offset %08Xh miscompared patterns %08Xh and %08Xh during %s pass. | CPU Motherboard | L2 Cache Pattern Test | cache.mdm |
0700-0419 | The cache improperly changed system memory during an 'invalidate' at line %d. | CPU Memory Motherboard | L2 Cache Walking Bit Test | cache.mdm |
0700-041D | Level 2 cache failure. Cache offset %08Xh miscompare during %s pass at line %d. | CPU Motherboard | L2 Cache Walking Bit Test | cache.mdm |
0700-0519 | The cache improperly changed system memory during an 'invalidate' at line %d. | CPU Memory Motherboard | L2 Cache MATS Test | cache.mdm |
0700-051A | Cache offset %08Xh miscompare at line %d. | CPU Motherboard | L2 Cache MATS Test | cache.mdm |
08XX-XXXX | caci437.mdm | |||
09XX-XXXX | cacvesuv.mdm | |||
0AXX-XXXX | cisco.mdm | |||
0BXX-XXXX | No failures | N/A | No tests | cpu.mdm |
0D00-XXXX | ddinit.mim | |||
0E00-XXXX | dellsys.msm | |||
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
0F00-01XX | Hard Drive Cable Motherboard | Device Self Test | disk.mdm | |
0F00-02XX | Hard Drive Cable Motherboard | Read Test | disk.mdm | |
0F00-03XX | Hard Drive Cable Motherboard | Write Test | disk.mdm | |
0F00-04XX | Hard Drive Cable Motherboard | Seek Test | disk.mdm | |
0FXX-05XX | CD Drive Audio Card Cable Motherboard | CD-ROM Audio Test | disk.mdm | |
0F00-06XX | Hard Drive Cable Motherboard | S.M.A.R.T. Short Self Test | disk.mdm | |
0F00-07XX | Hard Drive Cable Motherboard | S.M.A.R.T. Long Self Test | disk.mdm | |
0FXX-0AXX | Hard Drive Cable Motherboard | Zero Drive Test | disk.mdm | |
0FXX-0BXX | Hard Drive Cable Motherboard | Invert Data Test | disk.mdm | |
0FXX-0CXX | Hard Drive Cable Motherboard | Sector Uniqueness Test | disk.mdm | |
0FXX-0DXX | Hard Drive Cable Motherboard | Start unit (Idle) command | disk.mdm | |
0FXX-0EXX | Hard Drive Cable Motherboard | Stop unit (Standby) command | disk.mdm | |
0FXX-0FXX | Hard Drive Cable Motherboard | Write Random Test | disk.mdm | |
0F00-10XX | Hard Drive Cable Motherboard | Enable S.M.A.R.T. operations | disk.mdm | |
0F00-11XX | Hard Drive Cable Motherboard | Disable S.M.A.R.T. operations | disk.mdm | |
0F00-12XX | Hard Drive Cable Motherboard | S.M.A.R.T. Test | disk.mdm | |
0F00-13XX | Hard Drive Cable Motherboard | Confidence Test | disk.mdm | |
0F00-1348 | Target drive aborted the command | Hard Drive Cable Motherboard | Confidence Test | disk.mdm |
0FXX-14XX | Tape Drive Cable Motherboard | Tape Retension Test | disk.mdm | |
0F00-15XX | Hard Drive Cable Motherboard | S.M.A.R.T. Off-line Test | disk.mdm | |
0FXX-16XX | Hard Drive Cable Motherboard | Signals Test | disk.mdm | |
0FXX-17XX | Cable Motherboard | Ultra DMA 66 Cable Test | disk.mdm | |
0FXX-18XX | Hard Drive Cable Motherboard | Transfer Rate Test | disk.mdm | |
0FXX-19XX | Hard Drive Cable Motherboard | Log Test | disk.mdm | |
0F00-1AXX | Hard Drive Cable Motherboard | Verify Test | disk.mdm | |
0FXX-1BXX | Drive Cable Motherboard | Media Eject Test | disk.mdm | |
0FXX-1CXX | CD Drive Audio Card Cable Motherboard | CD-ROM Audio Test On | disk.mdm | |
0FXX-1DXX | CD Drive Audio Card Cable Motherboard | CD-ROM Audio Test Off | disk.mdm | |
0FXX-1EXX | Hard Drive Cable Motherboard | Zero Drive Test, No Verify | disk.mdm | |
0FXX-1FXX | CD Drive Audio Card Cable Motherboard | CD-ROM Audio Test With File On | disk.mdm | |
0FXX-20XX | CD Drive Audio Card Cable Motherboard | CD-ROM Audio Test With File Off | disk.mdm | |
0FXX-21XX | Hard Drive Cable Motherboard | Format Test | disk.mdm | |
0FXX-XX25 | Command was successful with some recovery action performed | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX26 | Device cannot be accessed, possibly medium not present | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX27 | Flaw in medium or an error in the recorded data. If this is a removable media device, try different media | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX28 | Non-recoverable hardware error | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX29 | Illegal request - possible use of incorrect media | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX2A | Reset or medium changed | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX2B | Read was requested on a block that is protected | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX2C | Blank check | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX2D | Vendor specific error | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX2E | Copy aborted | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX2F | Aborted command | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX30 | Equal | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX31 | Volume overflow | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX32 | Data compare error | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX33 | Reserved for future use | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX34 | Timeout waiting for drive not busy | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX35 | Expected request for command | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX36 | Expected request for data in | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX37 | Expected request for data out | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX37 | Data transfer count doesn't match expected count | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX39 | Not enough data was transferred | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX3A | Illegal length indication | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX3B | End of media detected | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX3C | Media change requested | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX3D | An unknown error occurred | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX3E | A possible failure is predicted by the drive's S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Technology) status. It is advisable to immediately back up your data. | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX3F | User aborted the test | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX40 | Address mark not found or media error | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX41 | No media in removable media device | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX42 | Address not found | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX43 | Media changed | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX44 | Uncorrectable data error or media is write protected | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX45 | Ultra DMA CRC error detected | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX46 | Drive failed to detect an ECC error | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX47 | Timeout waiting for DSC to be asserted | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX48 | Target drive aborted the command | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX49 | A target or master abort was encountered while transferring data | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX4A | S.M.A.R.T. off-line data collection was never started | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX4B | S.M.A.R.T. off-line data collection was suspended by a host command | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX4C | S.M.A.R.T. off-line data collection was aborted by a host command | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX4D | S.M.A.R.T. off-line data collection was aborted by a fatal error | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX4E | Unknown S.M.A.R.T. off-line data collection status | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX4F | Device Address or Command Select (DA, CS0-) signals are not working | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX50 | Control Select (CS1-) signal is not working | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX51 | The Interrupt Request (INTRQ-) signal is not working | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX52 | The Data signals (DD) are not working | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX53 | A PIO transfer failed. The IORDY signal may not be working correctly | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX54 | The Passed Diagnostics (PDIAG-) signal was not detected | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX56 | Too much data was transferred | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX57 | The removable media in the drive does not match the requested density | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX58 | The self-test routine was aborted by the host | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX59 | The self-test routine was aborted by the host with a hard or soft reset | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX5A | A fatal or unknown error occurred during the self-test routine | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX5B | The self-test failed for an unknown reason | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX5C | The self-test failed the electrical portion of the test | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX5D | The self-test failed the servo portion of the test | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX5E | The self-test failed the read portion of the test | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX5F | An invalid status value was returned by the self-test | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX60 | ATAPI devices do not support the identify device command | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX61 | Timeout waiting for DRQ to be asserted | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX62 | An 80-pin Ultra DMA 66/100 cable was not detected | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX63 | Device initialization failed | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX64 | Prior DST failure logged in the SMART self-test log | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX65 | IDE CD-RW/DVD+RW format test failed | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX66 | The self-test code took an unexpected path | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX67 | The self-test took too long to run | Hard Drive Cable Motherboard | disk.mdm | |
0FXX-XX68 | The media is still in the device | Hard Drive Cable Motherboard | disk.mdm | |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
1100-011C | A keystroke ended the change line test. | Floppy Drive Motherboard | Diskette Drive Change Line Test | diskette.mdm |
1100-011D | The change line event did not occur. | Floppy Drive Motherboard | Diskette Drive Change Line Test | diskette.mdm |
1100-021D | The change line event did not occur. | Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0220 | The specified cylinder range parameters are invalid. | User error Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0221 | The disk BIOS operation resulted in an error code of %2.2Xh. | Floppy Drive Motherboard BIOS | Diskette Drive Seek Test | diskette.mdm |
1100-0222 | The BIOS did not recognize the command code %2.2Xh. | BIOS Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0223 | The diskette is write protected. | User error Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0224 | The BIOS reported an invalid sector status for the position %s | Floppy Drive Motherboard BIOS | Diskette Drive Seek Test | diskette.mdm |
1100-0225 | The BIOS reported an error on attempting to reset the device. | Floppy Drive Motherboard BIOS | Diskette Drive Seek Test | diskette.mdm |
1100-0226 | A data error which could not be corrected was detected at %s | Diskette Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0227 | A correctable (soft) data error occurred on the diskette at %s | Diskette Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0228 | A diskette controller failure occurred. | Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-0229 | A seek to position %s failed. | Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-022A | An operation on the drive timed out. | Floppy Drive Motherboard | Diskette Drive Seek Test | diskette.mdm |
1100-031D | The change line event did not occur. | Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-0320 | The specified cylinder range parameters are invalid. | User error Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-0321 | The disk BIOS operation resulted in an error code of %2.2Xh. | Floppy Drive Motherboard BIOS | Diskette Drive Read Test | diskette.mdm |
1100-0322 | The BIOS did not recognize the command code %2.2Xh. | BIOS Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-0323 | The diskette is write protected. | User error Floppy Drive | Diskette Drive Read Test | diskette.mdm |
1100-0324 | The BIOS reported an invalid sector status for the position %s | Floppy Drive Motherboard BIOS | Diskette Drive Read Test | diskette.mdm |
1100-0325 | The BIOS reported an error on attempting to reset the device. | Floppy Drive Motherboard BIOS | Diskette Drive Read Test | diskette.mdm |
1100-0326 | A data error which could not be corrected was detected at %s | Diskette Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-0327 | A correctable (soft) data error occurred on the diskette at %s | Diskette Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-0328 | A diskette controller failure occurred. | Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-0329 | A seek to position %s failed. | Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-032A | An operation on the drive timed out. | Floppy Drive Motherboard | Diskette Drive Read Test | diskette.mdm |
1100-041D | The change line event did not occur. | Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-041F | The data values read back do not match those written. | Diskette Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0420 | The specified cylinder range parameters are invalid. | User error Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0421 | The disk BIOS operation resulted in an error code of %2.2Xh. | Floppy Drive Motherboard BIOS | Diskette Drive Write Test | diskette.mdm |
1100-0422 | The BIOS did not recognize the command code %2.2Xh. | BIOS Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0423 | The diskette is write protected. | User error Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0424 | The BIOS reported an invalid sector status for the position %s | Floppy Drive Motherboard BIOS | Diskette Drive Write Test | diskette.mdm |
1100-0425 | The BIOS reported an error on attempting to reset the device. | Floppy Drive Motherboard BIOS | Diskette Drive Write Test | diskette.mdm |
1100-0426 | A data error which could not be corrected was detected at %s | Diskette Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0427 | A correctable (soft) data error occurred on the diskette at %s | Diskette Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0428 | A diskette controller failure occurred. | Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-0429 | A seek to position %s failed. | Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
1100-042A | An operation on the drive timed out. | Floppy Drive Motherboard | Diskette Drive Write Test | diskette.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
12XX-XXXX | drsc.mdm | |||
13XX-XXXX | dsleep.mdm | |||
14XX-XXXX | dvd.mdm | |||
15XX-XXXX | es2828.mdm | |||
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
1BXX-01XX | Sound Card Motherboard | Software Reset Test | genaudio.mdm | |
1BXX-02XX | Sound Card Motherboard | Interrupt Test | genaudio.mdm | |
1BXX-03XX | Sound Card Motherboard | Register Test | genaudio.mdm | |
1BXX-04XX | Sound Card Motherboard | DMA Test | genaudio.mdm | |
1BXX-05XX | Speaker Sound Card Cable Motherboard | Synthesized Tone Test | genaudio.mdm | |
1BXX-06XX | Speaker Sound Card Cable Motherboard | Analog Sound Playback Test | genaudio.mdm | |
1B22-061B | The user’s response indicated a failure. | Speaker Sound Card Cable Motherboard | Analog Sound Playback Test | genaudio.mdm |
1BXX-07XX | Microphone Speaker Sound Card Cable Motherboard | Record and Playback Test | genaudio.mdm | |
1B22-071B | The user’s response indicated a failure. | Microphone Speaker Sound Card Cable Motherboard | Record and Playback Test | genaudio.mdm |
1BXX-08XX | Cable Sound Card Motherboard | Line Input Test | genaudio.mdm | |
1BXX-09XX | Sound Card Cable Motherboard | Tone/Volume Test | genaudio.mdm | |
1BXX-0AXX | Cable Sound Card Motherboard | CD Line In Connection Test | genaudio.mdm | |
1BXX-0BXX | Sound Card Cable Motherboard | Internal Audio Loopback Test | genaudio.mdm | |
1BXX-0CXX | Sound Card Cable Motherboard | Internal MIDI Loopback Test | genaudio.mdm | |
1BXX-0DXX | Speaker Sound Card Cable Motherboard | Optional Internal Speaker Test | genaudio.mdm | |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
1CXX-XXXX | grfxmem.mdm | |||
1DXX-XXXX | i2c8584.mdm | |||
1EXX-XXXX | i440xx.mdm | |||
1FXX-XXXX | i450nx.mdm | |||
20XX-XXXX | i820mch.mdm | |||
21XX-XXXX | i840mch.mdm | |||
22XX-XXXX | iaudio.mdm | |||
23XX-XXXX | ieee1394.mdm | |||
24XX-XXXX | imchecc.mdm | |||
25XX-XXXX | inspiron.mdm | |||
26XX-XXXX | ioapic.mdm | |||
27XX-XXXX | Motherboard | ioctlr.mdm | ||
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
2A00-0119 | IR port is not working properly. Failed checking UART INT_EN reg static bits. | Motherboard | Slow IR register test | ir.mdm |
2A00-011A | IR port is not working properly. Failed checking UART INT_ID reg static bits. | Motherboard | Slow IR register test | ir.mdm |
2A00-011B | IR port is not working properly. Failed checking MCR reg static bits. | Motherboard | Slow IR register test | ir.mdm |
2A00-011C | IR port is not working properly. Failed clearing LSR bits. | Motherboard | Slow IR register test | ir.mdm |
2A00-011D | IR port is not working properly. Failed clearing MSR bits. | Motherboard | Slow IR register test | ir.mdm |
2A00-011E | IR port is not working properly. Failed checking IID static bits. | Motherboard | Slow IR register test | ir.mdm |
2A00-011F | IR port is not working properly. Failed checking THRE & TXMT bits in LSR. | Motherboard | Slow IR register test | ir.mdm |
2A00-0120 | IR port is not working properly. Failed basic Scratch Reg test. | Motherboard | Slow IR register test | ir.mdm |
2A00-0121 | IR port is not working properly. Found UART, but not 550A. | Motherboard | Slow IR register test | ir.mdm |
2A00-0122 | IR port is not working properly. Failed complete scratch reg test. | Motherboard | Slow IR register test | ir.mdm |
2A00-0123 | IR port is not working properly. No interrupt received. | Motherboard | Slow IR register test | ir.mdm |
2A00-0224 | IR port is not working properly. Timeout waiting for Tx to empty. | Motherboard | Slow IR loopback test | ir.mdm |
2A00-0225 | IR port is not working properly. Failed trying to empty Rx. | Motherboard | Slow IR loopback test | ir.mdm |
2A00-0226 | IR port is not working properly. Timed out waiting for 0x%02X loopBack. | Motherboard | Slow IR loopback test | ir.mdm |
2A00-0227 | IR port is not working properly. After Tx=0x%02X, Rx=0x%02X, failed test. | Motherboard | Slow IR loopback test | ir.mdm |
2A00-042D | IR port is not working properly. Failed reading SMC_ID_HI, data = 0x%02X, s/b 0x10. | Motherboard | Fast IR register test | ir.mdm |
2A00-042E | IR port is not working properly. Failed reading SMC_ID_LO, data = 0x%02X, s/b 0xB8. | Motherboard | Fast IR register test | ir.mdm |
2A00-042F | IR port is not working properly. Failed reading CHIP_ID, data = 0x%02X, s/b 0xF1 or 0xF2. | Motherboard | Fast IR register test | ir.mdm |
2A00-0430 | IR port is not working properly. No interrupt received. | Motherboard | Fast IR register test | ir.mdm |
2A00-0431 | IR port is not working properly. Failed checking BofLow reg., data = 0x%02X. | Motherboard | Fast IR register test | ir.mdm |
2A00-0432 | IR port is not working properly. FIFO not empty after reset!. | Motherboard | Fast IR register test | ir.mdm |
2A00-0433 | IR port is not working properly. FIFO full early, count=%d. | Motherboard | Fast IR register test | ir.mdm |
2A00-0434 | IR port is not working properly. FIFO not full after 128 bytes. | Motherboard | Fast IR register test | ir.mdm |
2A00-0435 | IR port is not working properly. Failed reading back FIFO got 0x%02X, s/b 0x%02X. | Motherboard | Fast IR register test | ir.mdm |
2A00-0436 | IR port is not working properly. FIFO empty early, count=%d. | Motherboard | Fast IR register test | ir.mdm |
2A00-0437 | IR port is not working properly. FIFO not empty after 128 bytes. | Motherboard | Fast IR register test | ir.mdm |
2A00-0438 | IR port is not working properly. DMA channel not configured by BIOS. | Motherboard | Fast IR register test | ir.mdm |
2A00-0439 | IR port is not working properly. Failed, could not allocate DMA buffer. | Motherboard | Fast IR register test | ir.mdm |
2A00-043A | IR port is not working properly. Failed, DmaSize=%d, s/b %d. | Motherboard | Fast IR register test | ir.mdm |
2A00-043B | IR port is not working properly. Failed, byte %d = 0x%02X, s/b 0x%02X. | Motherboard | Fast IR register test | ir.mdm |
2A00-053C | IR port is not working properly. Failed | Motherboard | Fast IR loopback test | ir.mdm |
2A00-053D | IR port is not working properly. Timed out waiting for EOM | Motherboard | Fast IR loopback test | ir.mdm |
2A00-053E | IR port is not working properly. Failed | Motherboard | Fast IR loopback test | ir.mdm |
2A00-053F | IR port is not working properly. Failed | Motherboard | Fast IR loopback test | ir.mdm |
2A00-0540 | IR port is not working properly. Failed | Motherboard | Fast IR loopback test | ir.mdm |
2A00-0541 | IR port is not working properly. Failed | Motherboard | Fast IR loopback test | ir.mdm |
2A00-0542 | IR port is not working properly. Failed | Motherboard | Fast IR loopback test | ir.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
2C00-0119 | Unable to read keyboard %s port. Read 0xFFFF from the port. | Motherboard | Controller Test | keyboard.mdm |
2C00-011A | Unable to read keyboard test inputs. A read of the keyboard controller's test port returned all ones. | Motherboard | Controller Test | keyboard.mdm |
2C00-021C | The test was stopped before all keys on the keyboard were pressed. | Keyboard Cable Motherboard | Key Sequence Test | keyboard.mdm |
2C00-031B | The user indicated that the results of the test were unsatisfactory. | Keyboard Cable Motherboard | Interactive Test | keyboard.mdm |
2C00-041D | Stuck key detected. The keyboard is continuously transmitting a scan code of %Xh. | Keyboard Cable | Stuck Key Test | keyboard.mdm |
2C00-051B | The user indicated that the results of the test were unsatisfactory. | Keypad Cable Motherboard | External Keypad Test | keyboard.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
2D00-0126 | Timeout waiting for core read. Read bit (0x10) did not clear in DSP register (0xd8). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0127 | Timeout waiting for core write. Write bit (0x08) did not clear in DSP register (0xd8). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0130 | Invalid data was read from DSP register. Expected 0x%x, read 0x%x from DSP register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0132 | Invalid checksum read from DSP RAM. Expected 0x%x, read 0x%x. | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0133 | Invalid version read from DSP RAM. Expected 0x%x, read 0x%x. | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0138 | Invalid data was read from scratch register. Expected 0x%x, read 0x%x from scratch register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0139 | Invalid data was read from LCR register. Expected 0x%x, read 0x%x from LCR register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0140 | Invalid data was read from FCR register. Expected 0x%x, read 0x%x from FCR register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0141 | Invalid data was read from LSR register. Expected 0x%x, read 0x%x from LSR register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0142 | Invalid data was read from MSR register. Expected 0x%x, read 0x%x from MSR register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0143 | Invalid data was read from RBR register. Expected 0x%x, read 0x%x from RBR register (0x%x). | Modem Motherboard | Mimic Test | l56xmf.mdm |
2D00-0237 | PLL did not lock at 60MHz. Read DSP RAM location (0x1801), was equal to 0. | Modem Motherboard | PLL Test | l56xmf.mdm |
2D00-0325 | DSP RAM check low/high failed. Expected 0x00, read 0x%x from DSP register (0x35). | Modem Motherboard | DSP RAM Test | l56xmf.mdm |
2D00-0326 | Timeout waiting for core read. Read bit (0x10) did not clear in DSP register (0xd8). | Modem Motherboard | DSP RAM Test | l56xmf.mdm |
2D00-0327 | Timeout waiting for core write. Write bit (0x08) did not clear in DSP register (0xd8). | Modem Motherboard | DSP RAM Test | l56xmf.mdm |
2D00-0428 | Invalid data was read from DSP register. Write bit (0x%x) did not clear in DSP register (0x%x). | Modem Motherboard | Interrupt Test | l56xmf.mdm |
2D00-0429 | Invalid data was read from DSP register. Write bit (0x%x) did not clear in DSP register (0x%x). | Modem Motherboard | Interrupt Test | l56xmf.mdm |
2D00-0430 | Invalid data was read from DSP register. Expected 0x%x, read 0x%x from DSP register (0x%x). | Modem Motherboard | Interrupt Test | l56xmf.mdm |
2D00-0431 | Did not receive an interrupt. Expected 0x%x interrupts, got 0x%x interrupts. | Modem Motherboard | Interrupt Test | l56xmf.mdm |
2D00-0432 | Invalid checksum read from DSP RAM. Expected 0x%x, read 0x%x. | Modem Motherboard | Interrupt Test | l56xmf.mdm |
2D00-0433 | Invalid version read from DSP RAM. Expected 0x%x, read 0x%x. | Modem Motherboard | Interrupt Test | l56xmf.mdm |
2D00-0528 | Invalid data was read from DSP register. Write bit (0x%x) did not clear in DSP register (0x%x). | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0529 | Invalid data was read from DSP register. Write bit (0x%x) did not clear in DSP register (0x%x). | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0530 | Invalid data was read from DSP register. Expected 0x%x, read 0x%x from DSP register (0x%x). | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0532 | Invalid checksum read from DSP RAM. Expected 0x%x, read 0x%x. | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0533 | Invalid version read from DSP RAM. Expected 0x%x, read 0x%x. | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0534 | Data mode not detected. Read DSP RAM (0x3a), data mode bit (0x8) not set. | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0535 | Data mode did not reset. Read DSP RAM (0x3a), data mode bit (0x8) not clear. | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
2D00-0536 | Receiver never saw a valid frame, m_receiverInSync = %d | Modem Motherboard | Analog Loopback Test | l56xmf.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
2EXX-XXXX | laguna.mdm | |||
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
2F00-0119 | System memory failure. Read %08Xh, expected %08Xh at address %08Xh. | Memory Motherboard | Memory Address Line Test | memory.mdm |
2F00-0119 | System memory failure. Read %08Xh, expected %08Xh at address %08Xh. Suspected memory component located on %s at label %s | Memory Motherboard | Memory Address Line Test | memory.mdm |
2F00-0219 | System memory failure. Read %08Xh, expected %08Xh at address %08Xh. | Memory Motherboard | Memory Data Line Test | memory.mdm |
2F00-0219 | System memory failure. Read %08Xh, expected %08Xh at address %08Xh. Suspected memory component located on %s at label %s | Memory Motherboard | Memory Data Line Test | memory.mdm |
2F00-0419 | System memory failure. Read %08Xh, expected %08Xh at address %08Xh. | Memory Motherboard | Memory Bit Coupling Test | memory.mdm |
2F00-0419 | System memory failure. Read %08Xh, expected %08Xh at address %08Xh. Suspected memory component located on %s at label %s | Memory Motherboard | Memory Bit Coupling Test | memory.mdm |
2F00-0519 | System memory failure. ECC Error Encountered. Error is in 4K block starting at %08Xh | Memory Motherboard | Memory ECC Bit Coupling Test | memory.mdm |
2F00-0619 | System memory failure. ECC Error Encountered. Error is in 4K block starting at %08Xh | Memory Motherboard | Memory ECC Stuck Bit Test | memory.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
30XX-XXXX | mini3com.mdm | |||
3500-0119 | Could not disable mouse. The keyboard controller did not acknowledge a mouse disable command. | Motherboard | Mouse Test | mouse.mdm |
3500-011B | Could not set sampling rate. The keyboard controller did not accept a command to set the mouse's data sampling rate. | Motherboard | Mouse Test | mouse.mdm |
3500-011C | Could not enable mouse. The keyboard controller did not acknowledge a mouse enable command. | Motherboard | Mouse Test | mouse.mdm |
3500-011E | A parity error was detected. The keyboard controller status indicates a data parity (corrupted data) error. | Motherboard | Mouse Test | mouse.mdm |
3500-0121 | Timer expired before any keyboard or mouse data was found. | User error Mouse Motherboard | Mouse Test | mouse.mdm |
3500-0122 | Both buttons were detected as pressed. | Mouse Motherboard | Mouse Test | mouse.mdm |
3500-0219 | Could not disable mouse. The keyboard controller did not acknowledge a mouse disable command. | Motherboard | Pointing Stick Test | mouse.mdm |
3500-021B | Could not set sampling rate. The keyboard controller did not accept a command to set the mouse's data sampling rate. | Motherboard | Pointing Stick Test | mouse.mdm |
3500-021C | Could not enable mouse. The keyboard controller did not acknowledge a mouse enable command. | Motherboard | Pointing Stick Test | mouse.mdm |
3500-021E | A parity error was detected. The keyboard controller status indicates a data parity (corrupted data) error. | Motherboard | Pointing Stick Test | mouse.mdm |
3500-0221 | Timer expired before any keyboard or mouse data was found. | User error Pointing stick Motherboard | Pointing Stick Test | mouse.mdm |
3500-0222 | Both buttons were detected as pressed. | Pointing stick Motherboard | Pointing Stick Test | mouse.mdm |
3500-0319 | Could not disable mouse. The keyboard controller did not acknowledge a mouse disable command. | Motherboard | Touch Pad Tap Test | mouse.mdm |
3500-031B | Could not set sampling rate. The keyboard controller did not accept a command to set the mouse's data sampling rate. | Motherboard | Touch Pad Tap Test | mouse.mdm |
3500-031C | Could not enable mouse. The keyboard controller did not acknowledge a mouse enable command. | Motherboard | Touch Pad Tap Test | mouse.mdm |
3600-011A | Battery test failed - Charger should be shown as charging battery. | Battery Motherboard | Battery Charger Test | nbbatt.mdm |
3600-011B | Battery test failed - Charger should not be shown as charging battery. | Battery Motherboard | Battery Charger Test | nbbatt.mdm |
3600-0122 | Battery test failed - reporting disconnected charger. | User error Battery Motherboard | Battery Charger Test | nbbatt.mdm |
3600-0123 | Battery test failed - reporting attached charger. | User error Battery Motherboard | Battery Charger Test | nbbatt.mdm |
3700-0129 | Fan not running at correct speed or fan sensor incorrect | Fan | Fan On/Off Test | nbfan.mdm |
3700-011A | Fan test failed | Fan | Fan On/Off Test | nbfan.mdm |
3700-011B | Expected fan %s RPM of %d. Detected fan RPM = %d. | Fan | Fan On/Off Test | nbfan.mdm |
3900-0626 | Temperature sensor out of range, temp=%dC, min=%dC, max=%dC | Motherboard CPU | Sensor Range Test | nbtherm.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
3B00-0119 | Invalid manufacturer code. Expected %Xh but found %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-011A | Invalid device ID. Expected %Xh but found %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-011B | Word I/O failed for data pattern. Expected %Xh but found %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-011C | Byte I/O failed for data pattern %Xh. Expected %Xh but found %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-011D | Window change failed. Unable to select window %d. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-011E | Fast read of alternate value failed. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-011F | Station address register test failed. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0120 | EEPROM failure detected. Expected a 'data' checksum of %Xh but found %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0124 | Invalid interrupt count. Expected %Xh but found %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0125 | MII physical layer failed. Register %Xh access failed, value=%Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0126 | MII physical layer failed. Reset timeout. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0127 | MII physical layer failed. Reset failed, control register %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0128 | MII physical layer failed. Expected: %Xh Actual: %Xh Register: %Xh. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-013B | Non-specific adapter failure. Low level code %d. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-013C | Low level error adapter failure. Adapter command timeout error. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-013D | Low level error adapter failure. EEPROM access timeout error. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-013E | Low level error adapter failure. EEPROM product ID is mismatched with physical layer card. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-013F | Low level error adapter failure. MII physical layer not responding. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0140 | Invalid adapter configuration. The adapter was marked 'bad' during initialization. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0141 | Invalid adapter configuration. EISA adapter in ISA machine. | NIC Motherboard | NIC Register Test | nic.mdm |
3B00-0329 | Receive frame failed. Data does not match the transmit frame (size=%d). | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0332 | Receive frame failed. Invalid size, expected %d, but received %d. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0344 | Unable to issue a command to the adapter. Command %04Xh returned a code of %d. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0345 | Adapter failed to complete a command. Download to fifo failed to complete. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0346 | Adapter failed to complete a command. Data not looped back to receive FIFO. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0347 | Adapter failed to complete a command. Upload from fifo failed to complete. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0348 | Receive frame failed. Incomplete packet received. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0349 | Receive frame failed. Unknown receiver error. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-034A | Receive frame failed. Overrun error. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-034B | Receive frame failed. Oversize error. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-034C | Receive frame failed. Undersize error. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-034D | Receive frame failed. Framing error. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-034E | Receive frame failed. CRC error. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-034F | Receive frame failed, overflow status. | NIC Motherboard | NIC Internal Loopback Test | nic.mdm |
3B00-0529 | Receive frame failed. Data does not match the transmit frame (size=%d). | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0532 | Receive frame failed. Invalid size, expected %d, but received %d. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0544 | Unable to issue a command to the adapter. Command %04Xh returned a code of %d. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0545 | Adapter failed to complete a command. Download to fifo failed to complete. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0546 | Adapter failed to complete a command. Data not looped back to receive FIFO. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0547 | Adapter failed to complete a command. Upload from fifo failed to complete. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0548 | Receive frame failed. Incomplete packet received. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-0549 | Receive frame failed. Unknown receiver error. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-054A | Receive frame failed. Overrun error. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-054B | Receive frame failed. Oversize error. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-054C | Receive frame failed. Undersize error. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-054D | Receive frame failed. Framing error. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-054E | Receive frame failed. CRC error. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
3B00-054F | Receive frame failed, overflow status. | NIC Motherboard | NIC Bus Master Test | nic.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
3CXX-XXXX | nic8254x.mdm | |||
3D00-0119 | One or more of the parallel port registers failed the internal test. | Motherboard | Internal Test | parallel.mdm |
3D00-011C | Errors indicate that a loopback plug may be installed on this port! %s | Motherboard | Internal Test | parallel.mdm |
3D00-031F | Incorrect interrupt count. IRQ %d. Expected %d interrupts but received %d. | Motherboard | External Interrupt Test | parallel.mdm |
3D00-0320 | No interrupts were generated. This may be a problem with the parallel port, or the interrupt circuitry on the system.mdm, or the system.mdm's interrupt configuration. | Motherboard | External Interrupt Test | parallel.mdm |
3D00-0421 | Timeout error waiting for printer. Status Error (%Xh). | Motherboard | Printer Pattern Test | parallel.mdm |
3EXX-XXXX | pbs.mdm | |||
3FXX-XXXX | pci.mdm | |||
41XX-XXXX | pnp.mdm | |||
44XX-XXXX | scsi.mdm | |||
4500-0119 | Port is operating outside of allowable speed tolerances. Port base address %Xh is transmitting at %d cps | Motherboard | Baud Rate Test | serial.mdm |
4500-011A | Real time clock is not functioning. System BIOS reports repeated failure to read the clock. The serial tests make use of the system.mdm real time clock for determining elapsed time | Motherboard | Baud Rate Test | serial.mdm |
4500-011B | Real time clock is not functioning. System BIOS can no longer read the clock. The serial tests make use of the system.mdm real time clock for determining elapsed time | Motherboard | Baud Rate Test | serial.mdm |
4500-021C | Incorrect number of interrupts received. Port base address %Xh, irq %d, received %d interrupts but was expecting 1. | Motherboard | Interrupt Test | serial.mdm |
4500-031D | Failure on Modem Control Register loopback. Port base address %Xh expected character %02x but received %02x. | Motherboard | Internal Transmit Test | serial.mdm |
4500-031E | Failure on internal loopback. Port base address %Xh. | Motherboard | Internal Transmit Test | serial.mdm |
4500-031F | Failure on Line Status Register loopback. Port base address %Xh, transmit buffer not empty. | Motherboard | Internal Transmit Test | serial.mdm |
4500-0320 | Failure on Line Status Register loopback. Port base address %Xh, expected data not received. | Motherboard | Internal Transmit Test | serial.mdm |
4500-0321 | Failure on Line Status Register loopback. Port base address %Xh, overrun error not detected. | Motherboard | Internal Transmit Test | serial.mdm |
4500-0322 | Failure on Line Status Register loopback. Port base address %Xh, transmit buffer not empty on retransmission. | Motherboard | Internal Transmit Test | serial.mdm |
4600-011B | The test requested a specific Type %d structure that does not exist. | BIOS | BIOS Information | smbios.mdm |
4600-011D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | BIOS Information | smbios.mdm |
4600-021A | Unable to access device state. SMI handler returned error (%xh) while trying to retrieve the device state. | BIOS | Environment Information | smbios.mdm |
4600-021B | The test requested a specific Type %d structure that does not exist. | BIOS | Environment Information | smbios.mdm |
4600-021D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | Environment Information | smbios.mdm |
4600-021E | (variable message text) | BIOS | Environment Information | smbios.mdm |
4600-031B | The test requested a specific Type %d structure that does not exist. | BIOS | I/O Information | smbios.mdm |
4600-031D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | I/O Information | smbios.mdm |
4600-041B | The test requested a specific Type %d structure that does not exist. | BIOS | Memory Information | smbios.mdm |
4600-041D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | Memory Information | smbios.mdm |
4600-051B | The test requested a specific Type %d structure that does not exist. | BIOS | Processor Information | smbios.mdm |
4600-051D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | Processor Information | smbios.mdm |
4600-061B | The test requested a specific Type %d structure that does not exist. | BIOS | System Information | smbios.mdm |
4600-061C | Device State Out of Acceptable Range. | BIOS | System Information | smbios.mdm |
4600-061D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | System Information | smbios.mdm |
4600-071B | The test requested a specific Type %d structure that does not exist. | BIOS | Battery Information | smbios.mdm |
4600-071D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | Battery Information | smbios.mdm |
4600-081B | The test requested a specific Type %d structure that does not exist. | BIOS | Pointing Device Information | smbios.mdm |
4600-081D | Module does not support the system.mdm SMBIOS specification revision. | BIOS | Pointing Device Information | smbios.mdm |
47XX-XXXX | smbus.mdm | |||
48XX-XXXX | smi.mdm | |||
49XX-XXXX | swecc.mdm | |||
4AXX-XXXX | symbios.mdm | |||
4BXX-XXXX | sysbdmon.mdm | |||
4C00-0121 | Incorrect data testing the DMA %s. Port: %02Xh Expected: %02Xh Actual: %02Xh. | Motherboard | DMA Functionality Test | system.mdm |
4C00-021D | The 'Seconds' register is not updating. The register is not updating or is updating too slowly. The part may be bad or the 32-KHz crystal might not be functioning. | Motherboard | RTC Functionality Test | system.mdm |
4C00-021E | The time registers did not increment correctly. The RTC did not generate the expected time after it was set for the maximum value and allowed to roll-over. | Motherboard | RTC Functionality Test | system.mdm |
4C00-031F | The CMOS battery failed. Status Register D of the RTC chip indicates that the CMOS is not valid because the backup battery is not working. | Battery Motherboard | CMOS Confidence Test | system.mdm |
4C00-0320 | CMOS failed the pattern test. Location: %Xh, Expected: %Xh, Actual: %Xh. | Motherboard | CMOS Confidence Test | system.mdm |
4C00-041A | The interrupt routine is not being called. Channel 0 (mode 0) is not generating interrupts. It might not be counting properly or the interrupt mechanism is not working. | Motherboard | Timer Functionality Test | system.mdm |
4C00-041B | Interrupt IRQ0 is at the wrong frequency. Channel 0 (mode 3) is generating the wrong interrupt count per second. Expected :%d, Actual: %d. | Motherboard | Timer Functionality Test | system.mdm |
4C00-041C | Channel 2 is not operating correctly. In mode %d, it is not correctly asserting and deasserting the OUT signal after being programmed. | Motherboard | Timer Functionality Test | system.mdm |
4C00-041C | Channel 2 is not operating correctly. No periodic ticks were generated. The realtime clock is probably not functioning. | Motherboard | Timer Functionality Test | system.mdm |
4C00-041C | Channel 2 is not operating correctly. Wrong time period (milliseconds) for a full count-down in mode %d. Expected: %d, Actual: %d. | Motherboard | Timer Functionality Test | system.mdm |
4C00-041C | Channel 2 is not operating correctly. The initial clock output level in mode %d is incorrect. Expected: %d Actual: %d. | Motherboard | Timer Functionality Test | system.mdm |
4C00-0522 | The interrupt controller, or a device attached to it, is not working. No interrupt detected for IRQ %d - %s. | Motherboard | PIC Functionality Test | system.mdm |
4C00-0619 | Speaker could not be heard. The operator replied 'No' to the prompt indicating that the tones were not heard from the speaker. | Speaker Audio card Motherboard | Speaker Functionality Test | system.mdm |
4C00-0726 | Failed to load and store constant 0.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0726 | Failed to load and store constant 1.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0726 | Failed to load and store constant 'pi'. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0726 | Failed to load and store constant log2 of 10. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0726 | Failed to load and store constant log2 of 'e'. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0726 | Failed to load and store constant log 2. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0726 | Failed to load and store constant ln 2. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load and store integer 1. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load integer 1 and store as short real 1.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load integer 1 and store as long real 1.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load integer 1 and store as BCD. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load integer 32767 and store as short real 32767.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load integer -32768 and store as short real -32768.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load short real -1.0 and store as integer -1. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load short real 0.0 and store as integer 0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load short real 1.0 and store as integer 1. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load long real -1.0 and store as integer -1. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load long real 0.0 and store as integer 0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0727 | Failed to load long real 1.0 and store as integer 1. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0728 | Wrong status after comparing 1.0 and 1.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0728 | Wrong status after comparing 3.0 and 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0728 | Wrong status after comparing 2.0 and 3.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0728 | Wrong status after 1.0 / 0.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0729 | Wrong stack tags after 'fadd' instruction. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-0729 | Wrong stack tags after 'faddp' instruction. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072A | Wrong status after 3.0 + 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072A | Wrong status after 3.0 - 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072A | Wrong status after 2.0 - 3.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072A | Wrong status after 3.0 * 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072A | Wrong status after 3.0 / 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072B | Calculation error of 3.0 / 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072B | Calculation error of the square root of 2.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072B | Calculation error of arctangent (tangent (pi/4.0)) * 4.0. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-072B | Calculation error of log2*1 -1) + 1) * 8. | Processor Motherboard | FPU Calculation Test | system.mdm |
4C00-082C | Wrong status after purposely performing an invalid operation. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082C | Wrong status after generating a denormalized operand. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082C | Wrong status after performing a divide by zero. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082C | Wrong status after generating an overflow. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082C | Wrong status after generating a precision failure. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082C | Wrong status after generating an underflow. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082D | No IRQ13 following an invalid result. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082D | No IRQ13 following a denormalized operand. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082D | No IRQ13 following a zero divide. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082D | No IRQ13 following an overflow. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082D | No IRQ13 following a precision exception. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-082D | No IRQ13 following an underflow. | Processor Motherboard | FPU Error Exception Test | system.mdm |
4C00-0923 | A PC card is not seated properly. Check the card in socket %c (index %Xh, base %Xh). | PC card Motherboard | PCMCIA Functionality Test | system.mdm |
4C00-092E | Unable to access any PCIC register. First error: Socket: %c (index %Xh, base %Xh) Register index: %Xh Test pattern: %Xh Data read: %Xh Bits tested: %Xh | Motherboard PC card | PCMCIA Functionality Test | system.mdm |
4C00-092F | One or more PCIC registers failed. First error: Socket: %c (index %Xh, base %Xh) Register index: %Xh Test pattern: %Xh Data read: %Xh Bits tested: %Xh | Motherboard PC card | PCMCIA Functionality Test | system.mdm |
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
4DXX-XXXX | tdir.mdm | |||
4E00-0119 | Unable to get register #%u mask. | Motherboard | Register Test | usb.mdm |
4E00-011A | Unable to read register #%u. | Motherboard | Register Test | usb.mdm |
4E00-011B | Unable to write register #%u. | Motherboard | Register Test | usb.mdm |
4E00-011C | Register #%u read or write failed Found:%02Xh Expected:%02Xh. | Motherboard | Register Test | usb.mdm |
4E00-011D | Register #%u read or write failed Found:%04Xh Expected:%04Xh. | Motherboard | Register Test | usb.mdm |
4E00-011E | Register #%u read or write failed Found:%08Xh Expected:%08Xh. | Motherboard | Register Test | usb.mdm |
4E00-021F | Unable to disable Intel UHCI interrupts. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0220 | Unable to reset Intel UHCI controller. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0221 | Unable to process End Point Descriptor | Motherboard | Memory Structure Test | usb.mdm |
4E00-0222 | Unable to allocate enough memory for Intel UHCI control structures. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0223 | Incorrect Memory Structure Test #%u requested. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0224 | FRNUM Register isn't walking frame list. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0225 | FmRemaining register is not decrementing | Motherboard | Memory Structure Test | usb.mdm |
4E00-0226 | FRNUM register indicates controller stopped polling at wrong index. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0227 | Expected the run/stop bit in USBCMD register to clear. Controller did not properly detect faulty transaction (bad TD PID) data. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0228 | USB controller did not generate the error interrupt that was expected. | Motherboard | Memory Structure Test | usb.mdm |
4E00-0229 | Unable to clear USBSTS register bit. | Motherboard | Memory Structure Test | usb.mdm |
4E00-022A | USB didn't set correct bits in USBSTS when given a bad TD PID | Motherboard | Memory Structure Test | usb.mdm |
4FXX-XXXX | Modem Motherboard | vd3xjs.mdm | ||
エラーコード | エラーメッセージ | 故障箇所 | テスト名 | モジュール名 |
51XX-XXXX | vdiccf.mdm | |||
5300-0119 | Detected a failure while writing and reading video memory. Video mode: %Xh (%dx%dx%d). Address %Xh, expected to read %Xh, but read %Xh instead. | Video Card Motherboard | Video Memory Test | video.mdm |
5300-011A | User-specified video mode not supported. | User Video Card LCD Panel | Video Memory Test | video.mdm |
5300-021B | Detected a failure while read/write testing the video Cursor Control Registers. Wrote %4.4X, but read back %4.4X. | Video Card LCD Panel Cable Motherboard | Video Hardware Test | video.mdm |
5300-021C | Detected a problem with retrace status. The retrace status bits do not appear to be changing state. | Video Card LCD Panel Cable Motherboard | Video Hardware Test | video.mdm |
5300-031E | The user's response indicated a failure of a text mode pattern using video mode: %Xh (%dx%dx%d). | Video Card LCD Panel Cable Motherboard | Text Mode Character Test | video.mdm |
5300-041E | The user's response indicated a failure of a text mode pattern using video mode: %Xh (%dx%dx%d). | Video Card LCD Panel Cable Motherboard | Text Mode Color Test | video.mdm |
5300-051D | The user's response indicated a failure of text page %d (in mode 2). | Video Card LCD Panel Cable Motherboard | Text Mode Pages Test | video.mdm |
5300-061F | The user's response indicated a failure of a graphic pattern using video mode: %Xh (%dx%dx%d). | Video Card LCD Panel Cable Motherboard | Graphics Mode Test | video.mdm |
5300-081A | User-specified video mode not supported. | User Video Card LCD Panel | Solid Colors Test | video.mdm |
5300-0820 | The user's response indicated a failure of one of the solid color patterns. | Video Card LCD Panel Cable Motherboard | Solid Colors Test | video.mdm |
5300-0921 | The user's response indicated a failure. | Video Card LCD Panel Cable Motherboard | LCD Pattern Test | video.mdm |
5300-0A21 | The user's response indicated a failure. | Video Card LCD Panel Cable Motherboard | LCD Circle Test | video.mdm |
5300-0B21 | The user's response indicated a failure. | Video Card LCD Panel Cable Motherboard | LCD Line Test | video.mdm |
55XX-XXXX | lsi.mdm | |||
56XX-XXXX | usb2.mdm |